If these stations all have XF, even if it's only a client, Color Tools will be present. i1Profiler can be installed for measuring on each machine without a license. Likewise, an XF client and i1P can be loaded on a laptop. The annoying part is the workaround, but the amount of shoe leather used should be the same.
It should not be necessary to completely reprofile the printer with the original It8 to realign its output, and the 234-patch chart included in Color Tools for optimization is an excellent choice--very nearly as good as the full profiling chart and measurable in a fraction of the time. If the printers in question are so unstable as to require weekly recalibration the entire problem might be rethought a little bit, e.g., the likelihood that the higher resolution of the TC-1617 (in near-neutrals) might be wasted.
------------------------------
Mike Strickler
MSP Graphic Services
Certified Fiery XF Partner
------------------------------
Original Message:
Sent: 01-19-2017 08:00 AM
From: Jeffrey Pelance
Subject: New TC1617x
For me it is not a 5 minute work-around. I have 7 XF Rip stations scattered throughout the building and all are running on a windows platform. The other program(s) are on my desktop computer (Mac) and is located in the front of the building and is not portable. For me to implement the i1Profiler I have to print the target, take it back to the desk, scan, save, go back out to the station, upload and implement. If it did not correct values fully, then the process starts all over again. Was only trying to eliminate walking off shoe leather. And it is not important that I use the TC-1617, am always on the lookout for new and better ideas and I learned at a young age that you never stop learning. If the TC-1617 makes my job a little easier I am all for it. At this point the way I have to try and use it is not. As far as the profiles go on the XF, I am re-calibrating several machines weekly here lately. I as well was not wanting to start a pi__ing contest on this, just looking to make my life a little easier.
------------------------------
Jeffrey Pelance
G7 Color Specialist
Indy Imaging, Inc.
Indianapolis IN
(317) 917-7938
------------------------------
Original Message:
Sent: 01-18-2017 11:21 AM
From: Mike Strickler
Subject: New TC1617x
I haven't, but I'm not particularly motivated to do so. How often do you find yourself making profiles for XF that a 5-minute workaround is onerous? There are other reasons to slow down, for example, to examine and correct your data (which requires another app as well). And not to start a sh_t storm (though it might), why is it critical for you to use the TC-1617?
------------------------------
Mike Strickler
MSP Graphic Services
------------------------------
Original Message:
Sent: 01-18-2017 07:06 AM
From: Jeffrey Pelance
Subject: New TC1617x
This is the procedure I am doing now as well. I was just curious if anyone had successfully implemented this chart into the Fiery XF library so you would not require another program. Streamlining the process you might say.
------------------------------
Jeffrey Pelance
G7 Color Specialist
Indy Imaging, Inc.
Indianapolis IN
(317) 917-7938
------------------------------
Original Message:
Sent: 01-16-2017 11:15 PM
From: Guowen Donny Yeo
Subject: New TC1617x
thats what i did on my XF.
------------------------------
DonnyYeo
Singapore
(659) 010-1049
<maskemail>Colorstandard@...</maskemail>
------------------------------
Original Message:
Sent: 01-16-2017 04:41 AM
From: Mike Strickler
Subject: New TC1617x
The only way I know of to use an unsupported chart in Fiery Printer Profiler is to measure it in an app that does support it and import the measurements. Print the TC-1617 chart using the intended output device/EPL, measure in i1P, save the measurements as a Profilemaker Lab CGATS (not spectral). From the Color Tools menu choose "Create Profile from Measurement" and import the CGATS file. At the end you'll need to place this file in the Working folder along with the EPL and use the Profile Connector to join them. This is probably more trouble than making the profile in i1P to begin with and then using Profile Connector, but if you lack a license for i1P this should work as an alternative.
Perhaps the upcoming XF v. 6.4 will directly support the TC-1617.
------------------------------
Mike Strickler
Principal
MSP Graphic Services
------------------------------
Original Message:
Sent: 01-15-2017 08:23 AM
From: Cory Sawatzki
Subject: New TC1617x
I would just like to see the response to this as well. Thank you.
------------------------------
Cory Sawatzki
President
Spotlight Print Consulting
Murfreesboro TN
(469) 879-5546
------------------------------
Original Message:
Sent: 01-13-2017 08:59 AM
From: Jeffrey Pelance
Subject: New TC1617x
Has anyone been successful creating this form for for use in the EFI Fiery XF rip?. If you have could you please provide me with information as to how you created and installed it. I would like to use this form while creating profiles but am not sure how to get it into Fiery XF/Color Tools. I am able to run this through i1Profiler but would much rather not switch programs back and forth and try to stick with one program in the Linearization/Icc Profile creation process. Any help would be much appreciated.
------------------------------
Jeffrey PelanceG7 Color SpecialistIndy Imaging, Inc.Indianapolis IN(317) 917-7938
------------------------------